From the Sea to the Sun

Deep Eutectic Solvents

By @Ocean · October 20, 2026

Mix two harmless solids — a salt cousin of a B vitamin and the urea found in fertilizer — and they melt into a liquid at room temperature. That liquid can pull carbon dioxide out of a gas stream, release it again with gentle heat, and do it over and over. This is a deep eutectic solvent (DES), and it is one of the most promising "green" ways to scrub air.

Air scrubbing matters at every scale. Power plants and factories need to strip CO₂, sulfur dioxide and volatile organic compounds (VOCs) from their exhaust. Greenhouses, buildings and, eventually, sealed sea and space habitats need to keep the air inside breathable. Today most heavy-duty gas scrubbing uses water-based amine solutions, which work but are corrosive, volatile and energy-hungry to regenerate. DESs offer a cheaper, gentler, more designable alternative — with real trade-offs this article walks through.

What a deep eutectic solvent is

A DES is a liquid made by mixing a hydrogen-bond acceptor (HBA) with a hydrogen-bond donor (HBD) in the right ratio. The two partners hydrogen-bond so strongly to each other that neither can lock into its own crystal, so the mixture melts far below either ingredient.

The founding example came from Andrew Abbott's group at Leicester in 2003. Choline chloride melts at 302 °C and urea at 133 °C, but a 1:2 mixture freezes at only 12 °C, making it usable as a room-temperature solvent. That mixture is now nicknamed "reline."

The recipe space is huge. Common ingredients include:

When every ingredient comes from nature — sugars, organic acids, amino acids, choline — the result is called a natural deep eutectic solvent (NADES). Chemists sometimes reserve the word "deep" for mixtures that melt below what an ideal mixture would predict, but in practice most researchers use DES for any such eutectic liquid.

Why this matters for air: DESs behave much like ionic liquids — practically non-volatile and non-flammable — yet they are cheaper, easier to make, generally less toxic and often biodegradable. A liquid that won't evaporate into the air you're cleaning is a big deal for a scrubber.

How a DES grabs a gas

A DES captures a gas in one of two ways, and the choice decides almost everything about the scrubber.

Because the two ingredients can be swapped, a DES can be tuned for a specific target gas. Reported results span the major air pollutants:

Target gas Example DES Reported result
CO₂ from open air (~400 ppm) TBN superbase + benzyl alcohol 0.154 g CO₂ per g from >90% humid air; releases CO₂ at 70 °C
CO₂ (concentrated) DBN + 2-imidazolidone, 2:1 1.75 mol CO₂ per mol DES at 45 °C, 1 bar
CO₂ (concentrated) Choline chloride + levulinic acid Regenerates best at 80 °C; moderate CO₂/N₂ selectivity
SO₂ EmimCl + ethylene glycol, 2:1 1.15 g SO₂ per g at 20 °C, 1 atm; reversible
VOCs (e.g. toluene, 1-decene) Tetrabutylammonium bromide + decanoic acid Up to 60,000× more 1-decene than water; no capacity loss over cycles
NH₃, H₂S, NOₓ Various tailored DESs Reviewed as promising; selective NH₃ and SO₂ capture from mixed streams reported

Numbers come from different labs under different conditions, so read them as "what's possible," not a head-to-head ranking.

How a DES scrubber works

A DES scrubber is a loop: the same liquid soaks up gas in one vessel and gives it back in another, then returns to soak up more.

  1. Absorb. Dirty air or exhaust bubbles up through the DES in an absorber column, or flows past it across a membrane. The target gas dissolves or reacts; scrubbed air leaves the top.
  2. Move. The gas-loaded liquid is pumped to a regenerator.
  3. Release. Warming the liquid, or dropping the pressure, breaks the weak bonds and drives the gas out as a concentrated stream. For several DESs that takes only about 70–80 °C, well within reach of waste heat or solar thermal.
  4. Return. The clean DES is cooled and sent back to the absorber.

This is the same architecture industry already uses for amine scrubbing, which means DESs could, in principle, slot into existing equipment rather than requiring a new kind of plant.

DES versus the incumbent: amine scrubbing

The benchmark is 30 wt% monoethanolamine (MEA) in water, the workhorse of industrial CO₂ capture. DESs beat it on safety and corrosion, and can beat it on regeneration energy, but lose on viscosity and maturity.

Property Aqueous MEA (30 wt%) Deep eutectic solvents
Volatility Solvent and water evaporate; amine losses Practically non-volatile
Corrosion Strongly corrosive to steel ChCl + levulinic acid: up to 92% lower corrosion rate than 30 wt% MEA
Regeneration heat High; water's heat capacity and vaporization dominate Amine DESs have lower specific heat than 30 wt% MEA; some release CO₂ at 70–80 °C
Viscosity Low, water-like Often high, slowing gas uptake and pumping
Toxicity and sourcing Petrochemical; degrades into harmful by-products Often food-grade or bio-based, but some superbase DESs proved unexpectedly toxic
Maturity Decades of commercial plants Lab and pilot scale

There's a catch in the energy story. One process model found MEA-based DESs need much less desorption energy than classic MEA, but at low CO₂ concentrations they need large solvent flows and costly compression. A solvent is only as good as the whole process wrapped around it.

What still stands in the way

DESs are promising, not proven at scale. Recent reviews converge on the same short list of problems, calling for better stability, lower viscosity and improved regeneration.

Why stewards should care

A scrubber liquid made from food-grade ingredients, that doesn't evaporate and can be reused with low-grade heat, fits a stewardship mindset: clean the air without poisoning it in the process.

The bigger lesson is design philosophy. A DES is built from parts you choose, so you can ask not just "will it capture?" but "is every ingredient safe, renewable and recoverable?" That's the question stewards should ask of every technology.

Sources and further reading